Jands Event 408 Manual

The Jands Event 408 is a professional lighting console designed for stage and event lighting control. It features 48 channels, 24 programmable submasters, 120 memory cues, MIDI compatibility, DMX512 output, chase programming, crossfade capabilities, and intuitive manual control. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: 48-channel manual control, 24 programmable submasters, 120 memory cues, DMX512 output, MIDI in/out/thru, chase programming, crossfade capabilities.

Feature	Description
Channel Faders	48 individual channel controls with dedicated faders
Submasters	24 programmable submasters for scene recall
Memory Cues	120 programmable memory locations
DMX Output	Standard DMX512 protocol output
MIDI Ports	MIDI in, out, and thru for external control
Chase Programming	Built-in chase sequence creation and playback
Crossfade Controls	Manual and timed crossfade capabilities
Grand Master	Overall intensity control for all channels
Blackout Button	Instant blackout of all outputs
Power Supply	Internal power supply with IEC connector

Installation

Unpack and inspect contents. Place on stable surface or mount in rack.

1. Connect DMX output: Use 3-pin XLR cable to connect to first DMX device.
2. Connect MIDI devices: Use standard MIDI cables for external control.
3. Connect power: Use included power cable to AC power source.
4. Connect dimmer packs: Ensure proper termination of DMX chain.

WARNING! Ensure proper grounding; use surge protection. Do not expose to moisture.

First-Time Setup

Power on console; initialize settings.

1. Set DMX address: Configure starting address for connected fixtures.
2. Program channels: Set channel levels and patch fixtures.
3. Create submasters: Program frequently used scenes to submasters.
4. Test outputs: Verify all connected fixtures respond correctly.

CAUTION! Always power down before connecting/disconnecting cables.

Specifications

• Channels: 48 manual channels
• Submasters: 24 programmable
• Memories: 120 programmable cues
• DMX Output: 512 channels standard
• MIDI: In, Out, Thru ports
• Chase Programs: Multiple programmable chases
• Crossfade: Manual and timed (0-999 seconds)
• Power Requirements: 100-240V AC, 50/60Hz
• Dimensions: Standard 19" rack mountable
• Weight: 8.5 kg (18.7 lbs)

Controls and Settings

Front Panel: Channel faders (1-48), Submaster faders (1-24), Grand Master, Blackout, Crossfade controls, Memory buttons.

Programming: Use RECORD button to store scenes, CHASE button for sequence programming, SUBMASTER buttons for scene assignment.

DMX Settings: Address configuration, protocol settings. MIDI Settings: Channel mapping, control assignments. Memory Management: Cue storage, playback options, timing settings.

Connecting Devices

DMX: 3-pin XLR output to first fixture. MIDI: Standard MIDI cables for external control.

1. Turn off all devices before connecting.
2. Connect DMX output to first fixture's input.
3. Terminate DMX chain with 120Ω resistor if required.
4. Connect MIDI devices for external control.

Tip: Use quality shielded cables for DMX to prevent signal degradation.

Programming Memories

Store and recall lighting scenes and cues.

1. Set levels: Adjust channel faders to desired levels.
2. Record memory: Press RECORD, select memory number, press ENTER.
3. Recall memory: Press MEMORY button, select number, press GO.
4. Edit memory: Recall memory, make changes, re-record.
5. Set timing: Adjust fade times for each memory cue.
6. Link memories: Create cue lists for automated shows.

WARNING! Save show file regularly to prevent data loss.

Chase Sequences

Create dynamic lighting sequences and patterns.

1. Access chase mode: Press CHASE button.
2. Select steps: Program individual step levels and timing.
3. Set speed: Adjust chase speed with tempo control.
4. Program direction: Forward, reverse, or random chase patterns.
5. Assign to submaster: Save chase to submaster for quick access.
6. Sync to MIDI: Synchronize chase tempo to external MIDI clock.

Tip: Use chases for dynamic effects like moving lights or color changes.

Care & Maintenance

Unplug before cleaning. Use compressed air for dust removal. Clean faders with appropriate contact cleaner.

CAUTION! Do not use liquid cleaners directly on console. Store in dry, temperature-controlled environment.

Regulatory Information

CE compliant: Meets European safety standards. FCC Part 15: Class A digital device. Copyright © Jands. For technical support, contact Jands support services or visit www.jands.com.au. Manufactured to industry standards for professional entertainment lighting.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No DMX output	Cable/address issues	Check DMX cable connections; verify fixture addresses; ensure proper termination.
Memory not saving	Memory protection/battery	Check memory protection settings; replace internal battery if needed.
Faders not responding	Calibration needed	Perform fader calibration procedure; check for physical damage.
MIDI not working	Cable/channel settings	Verify MIDI cable connections; check MIDI channel assignments.
Display issues	Power/connection	Check power supply; verify internal connections; reset console.

Reset: Power cycle console; factory reset if necessary.

Service: Contact authorized Jands service center; www.jands.com.au