Jandy 4 Function Spa Side Switch Manual

The Jandy 4 Function Spa Side Switch is a durable, water-resistant control panel designed for spa operation. It features four programmable functions including jet control, blower operation, light control, and temperature adjustment. Constructed with corrosion-resistant materials and rated for outdoor use, this switch provides convenient access to essential spa functions. Below are key sections for safety, features, installation, operation, programming, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Functions 6. Programming Options 7. Operation Guide 8. Maintenance & Care 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Water-resistant membrane keypad, LED indicators, 4 programmable function buttons, weather-resistant housing, and standard spa control wiring interface.

Feature	Description
Function Button 1	Programmable for jets, lights, or other spa functions
Function Button 2	Programmable for blower, temperature, or other spa functions
Function Button 3	Programmable for auxiliary functions or custom settings
Function Button 4	Programmable for system reset or special operations
LED Indicators	Visual feedback for active functions and system status
Water-resistant Design	IP66 rated for outdoor spa environment protection
Standard Wiring	Compatible with most spa control systems
Mounting Options	Surface mount or flush mount installation

Installation

Unpack and inspect contents. Ensure proper location selection for easy access and safety.

Select mounting location: Choose accessible spot near spa, away from direct water spray.
Prepare mounting surface: Clean and dry the installation area thoroughly.
Connect wiring: Follow color-coded wiring diagram for proper connections.
Secure switch: Mount using provided hardware and ensure water-tight seal.
Test functions: Verify all buttons operate correctly before finalizing installation.

WARNING! Always disconnect power before installation. Ensure proper grounding and waterproof connections.

First-Time Setup

Power on spa system; configure switch functions according to user preferences.

Access programming mode: Press and hold Function 1 + Function 4 for 5 seconds.
Assign functions: Use programming menu to assign desired operations to each button.
Set LED indicators: Configure LED behavior for each function.
Save settings: Press Function 4 to save and exit programming mode.
Test configuration: Verify all programmed functions operate as intended.

CAUTION! Ensure all electrical connections are secure and waterproof before powering on.

Specifications

Switch Type: 4-function membrane keypad with LED indicators
Water Resistance: IP66 rated for outdoor spa environments
Voltage Rating: 12V DC or 120V AC compatible
Operating Temperature: -20°C to 60°C (-4°F to 140°F)
Button Life: 1,000,000+ press cycles
Housing Material: UV-resistant ABS plastic
Wiring: Standard 6-conductor spa control cable
Dimensions: 4.5" x 2.5" x 0.75" (114mm x 64mm x 19mm)

Controls and Functions

Access functions via individual buttons. LED indicators show active operations.

Default Functions: Button 1 - Jets, Button 2 - Blower, Button 3 - Lights, Button 4 - Temperature/Reset

Programming: Enter programming mode to customize button functions. LED Indicators: Green for active, red for error, blinking for standby. Safety Features: Automatic timeout, low voltage protection, thermal overload protection. Operation: Press and release for function activation, press and hold for advanced options.

Programming Options

Customize each button function to match your spa configuration and preferences.

Enter programming mode: Power off, then press Function 1 + 4 simultaneously.
Select button to program: Use Function 3 to cycle through buttons.
Choose function: Use Function 2 to select from available operations.
Set parameters: Adjust timing, intensity, or other settings as needed.
Save and exit: Press Function 4 to confirm and return to normal operation.

Tip: Document your custom settings for future reference.

Operation Guide

Simple press-button operation for all spa functions.

Activate jets: Press Function 1 to start/stop water jets.
Control blower: Press Function 2 to operate air blower system.
Adjust lighting: Press Function 3 to cycle through light modes.
Temperature control: Press Function 4 to access temperature settings.
Combination functions: Press multiple buttons for special operations.
Status check: LED indicators show current system status.
Reset function: Press and hold Function 4 for system reset if needed.

WARNING! Do not operate switch with wet hands. Keep electrical components dry.

Maintenance & Care

Regular cleaning and inspection ensure long-term reliability.

Cleaning: Use mild soap and water with soft cloth. Avoid abrasive cleaners. Inspection: Monthly check for cracks, fading, or membrane damage. Electrical: Annual inspection of wiring connections and waterproof seals. Storage: Not applicable - designed for permanent outdoor installation.

CAUTION! Never use high-pressure water spray for cleaning. Disconnect power before maintenance.

Regulatory Information

UL Listed for spa and pool equipment. Complies with NEC Article 680 for swimming pools, fountains, and similar installations. CSA certified for Canadian market. Copyright © 2025 Jandy Products; trademarks of Fluidra USA. For technical support, visit www.jandy.com or contact 1-800-227-1442.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Button not responding	Membrane damage/moisture	Check for membrane tears; ensure dry operation; verify wiring.
LED not lighting	Power/LED failure	Check power supply; verify connections; replace if LED faulty.
Function not operating	Programming/wiring	Verify programming; check spa controller connections.
Intermittent operation	Loose connections	Inspect all wiring connections; ensure waterproof seals intact.
All functions inoperative	Power supply	Check main power; verify circuit breaker; inspect control system.

Reset: Power cycle spa system or use factory reset procedure.

Service: 1-800-227-1442; www.jandy.com