Jandy Apure35 Manual

The Jandy Apure35 is a high-performance salt chlorine generator designed for residential swimming pools up to 35,000 gallons. This system automatically converts salt into chlorine to keep your pool clean and sanitized. Features include digital controls, self-cleaning cell, built-in safety features, and compatibility with various pool systems. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Control panel, Salt cell, Flow sensor, Power supply unit, Temperature sensor.

Feature	Description
Control panel	Digital display with push-button controls
Salt cell	Self-cleaning titanium electrodes
Flow sensor	Monitors water flow for safety
Power supply	120V/240V compatible transformer
Temperature sensor	Monitors water temperature
Chlorine output	Adjustable from 20% to 100%
Super chlorinate	24-hour boost mode
Cell cleaning	Automatic reverse polarity
Error indicators	LED status lights for diagnostics
Waterproof housing	NEMA 4X rated enclosure

Installation

Unpack and inspect contents. Ensure proper location near pool equipment.

1. Mount control unit: Install on wall near pool equipment pad using provided brackets.
2. Install salt cell: Connect to pool plumbing after filter and before heater.
3. Electrical connection: Connect to dedicated GFCI circuit breaker.
4. Flow sensor installation: Install in plumbing line before salt cell.
5. Final connections: Verify all plumbing and electrical connections are secure.

WARNING! Installation must be performed by qualified professional. Ensure power is disconnected during installation.

First-Time Setup

Power on system; follow initial setup procedure.

1. Add salt: Add pool salt to achieve 3000-3500 ppm concentration.
2. Prime system: Run pump for 24 hours to dissolve salt completely.
3. Set chlorine output: Adjust percentage based on pool size and usage.
4. Calibrate sensors: Allow system to auto-calibrate during first 48 hours.
5. Test water: Verify proper salt levels and chlorine production.

CAUTION! Do not operate without proper water flow. Ensure salt is fully dissolved before activating cell.

Specifications

• Pool Capacity: Up to 35,000 gallons
• Chlorine Output: 1.45 lbs per day
• Salt Range: 3000-3500 ppm optimal
• Power Requirements: 120V/240V, 50/60Hz
• Cell Voltage: 24-28V DC
• Cell Current: 7.5A max
• Water Temperature: 50°F to 100°F operating range
• Flow Rate: Minimum 15 GPM required
• Warranty: 3 years on cell, 2 years on electronics
• Dimensions: Control unit: 12" x 9" x 5", Cell: 18" length

Controls and Settings

Access controls via front panel digital display and push buttons.

Control Panel: POWER, MENU, UP/DOWN arrows, ENTER, SUPER CHLORINATE, CELL CLEANING.

Settings: Chlorine output (20-100%), Pool type selection, Temperature display, Salt level display, Error codes, System status, Runtime hours, Cell cleaning cycle, Super chlorinate timer, Factory reset.

Connecting to Pool System

Integration with existing pool equipment and automation systems.

1. Pump connection: Requires compatible variable speed pump.
2. Heater integration: Connect to gas or heat pump heater.
3. Automation systems: Compatible with Jandy Aqualink and other systems.
4. Water features: Ensure proper flow for waterfalls and fountains.

Tip: Consult professional installer for complex system integrations.

Operation and Maintenance

Daily operation and routine maintenance procedures.

1. Daily: Check salt levels and chlorine production.
2. Weekly: Test water chemistry and clean cell if needed.
3. Monthly: Inspect cell for scale buildup.
4. Seasonal: Winterize system in freezing climates.
5. Annual: Professional inspection and calibration.

WARNING! Always turn off power before performing maintenance. Wear protective equipment when handling chemicals.

Safety Features

Built-in safety mechanisms for reliable operation.

• Flow switch: Prevents operation without water flow
• High salt shutdown: Protects cell from excessive salinity
• Low salt warning: Alerts when salt levels are too low
• Temperature protection: Shuts down at extreme temperatures
• Reverse polarity: Automatic cell cleaning cycle
• GFCI protection: Built-in ground fault protection

Care & Cleaning

Regular maintenance ensures optimal performance and longevity.

1. Cell cleaning: Use diluted muriatic acid solution for scale removal
2. Control unit: Wipe with damp cloth only
3. Plumbing connections: Check for leaks regularly
4. Electrical connections: Ensure tight and corrosion-free

CAUTION! Use only approved cleaning solutions. Never use abrasive cleaners on control panel.

Regulatory Information

UL listed and certified to NSF/ANSI 50 standards. Complies with local electrical codes. Copyright © 2024 Jandy Products. All rights reserved. For technical support, visit www.jandy.com or contact 1-800-227-1442.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No chlorine production	Low salt/Low flow	Check salt levels; verify pump operation; clean cell
High salt warning	Excessive salt	Dilute pool water; test salt concentration
Low salt warning	Insufficient salt	Add pool salt; allow 24 hours to dissolve
Flow error	Pump not running	Check pump operation; clean filter; verify flow switch
Cell cleaning required	Scale buildup	Perform manual cell cleaning; check water balance
Temperature error	Extreme water temp	Wait for temperature to normalize; check sensor

Reset: Press and hold MENU + POWER for 10 seconds.

Service: 1-800-227-1442; www.jandy.com