Jandy Flo Pro Manual

The Jandy Flo Pro is a high-performance pool pump designed for energy efficiency and quiet operation. It features variable speed technology, digital controls, durable construction, and compatibility with most pool filtration systems. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Variable speed motor, Digital control panel, Pump housing, Strainer basket, Power cord, Drain plugs.

Feature	Description
Variable Speed Motor	Energy efficient operation with adjustable RPM
Digital Control Panel	LCD display with touch controls
Strainer Basket	Large capacity for debris collection
Power Cord	Waterproof connection with safety features
Drain Plugs	For winterizing and maintenance
Pump Housing	Corrosion-resistant composite material
PRIME	Automatic priming function
FILTER	Standard filtration mode
BOOST	High-speed cleaning mode
ECONOMY	Energy-saving operation

Installation

Unpack and inspect contents. Position near pool equipment pad.

1. Connect to plumbing: Use appropriate PVC fittings and sealant.
2. Electrical connection: Connect to dedicated GFCI circuit.
3. Grounding: Ensure proper grounding according to local codes.
4. Position pump: Level surface with adequate ventilation.

WARNING! Electrical shock hazard - disconnect power before installation. Use licensed electrician for electrical connections.

First-Time Setup

Power on pump; follow initial setup procedure.

1. Prime the pump: Fill strainer basket with water, close lid securely.
2. Set time and date: Use control panel to configure system clock.
3. Program schedules: Set daily run times for different modes.
4. Configure speeds: Set RPM for each operating mode.

CAUTION! Ensure all plumbing connections are watertight before starting pump.

Specifications

• Motor Type: Variable Speed, 2.7 HP
• Flow Rate: Up to 120 GPM
• Voltage: 115/230V AC, 50/60Hz
• Maximum Pressure: 50 PSI
• Connections: 2" NPT threaded inlets/outlets
• Control: Digital LCD with programmable schedules
• Noise Level: Less than 65 dB at full speed
• Warranty: 3 years on motor, 1 year on electronics

Controls and Settings

Access control panel via front display. Buttons: POWER, MENU, UP/DOWN arrows, ENTER, MODE.

Display Indicators: RPM, GPM, Watts, Run Time, Schedule Status, Error Codes.

Speed Settings: PRIME (3450 RPM), FILTER (variable 750-3000 RPM), BOOST (3450 RPM), ECONOMY (1500 RPM). Schedule Programming: Daily timers for up to 8 programs. System Settings: Language, Time/Date, Factory Reset, Service Mode.

Connecting to Filtration System

Standard 2" plumbing connections. Compatible with sand filters, cartridge filters, and DE filters.

1. Turn off power to all pool equipment.
2. Connect suction line to pump inlet.
3. Connect pressure line to filter inlet.
4. Check for leaks after pressure test.

Tip: Use Teflon tape on all threaded connections for proper sealing.

Operation Modes

Four main operating modes for different pool maintenance needs.

1. PRIME Mode: Automatic priming sequence when pump is dry.
2. FILTER Mode: Standard filtration at programmed speed.
3. BOOST Mode: High-speed cleaning for vacuuming or spa operation.
4. ECONOMY Mode: Energy-saving operation for normal filtration.
5. Schedule Operation: Automatic mode switching based on programmed times.
6. Manual Override: Temporary speed adjustments without changing schedule.
7. Freeze Protection: Automatic activation when temperature drops below 38°F.
8. Service Mode: For maintenance and troubleshooting.

WARNING! Do not run pump dry for extended periods. Monitor pressure gauge regularly.

Maintenance Features

Self-diagnostic system with error codes. Automatic shut-off for dry running. Strainer basket clean-out reminder.

Care & Cleaning

Monthly maintenance: Clean strainer basket, inspect seals, check for leaks. Annual service: Lubricate seals, inspect motor bearings.

CAUTION! Disconnect power before performing any maintenance. Do not use high-pressure water on electrical components.

Regulatory Information

UL listed and CSA certified. Complies with Department of Energy regulations for pool pumps. Energy Star certified. Copyright © 2024 Jandy Products; trademarks of Fluidra. For technical support, visit www.jandy.com or contact 1-800-227-1442.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Pump won't start	Power supply/breaker	Check GFCI reset; verify power at outlet; check circuit breaker.
Loss of prime	Air leaks/basket	Check lid O-ring; ensure basket is clean; inspect suction lines.
Low flow	Clogged filter/basket	Clean strainer basket; backwash or clean filter; check for obstructions.
Motor overheating	Ventilation/voltage	Ensure adequate airflow; check voltage supply; clean motor vents.
Error codes displayed	System faults	Refer to error code chart in manual; reset system if needed.

Reset: Hold POWER + MENU for 10 seconds to factory reset.

Service: 1-800-227-1442; www.jandy.com