jandy jhp 2.0 manual

The Jandy JHP 2.0 is a high-performance pool heat pump designed for efficient and reliable pool heating. With advanced titanium heat exchanger technology, digital control system, and energy-saving operation, it provides optimal temperature control for residential pools. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Titanium heat exchanger, Digital control panel, Compressor unit, Water flow sensor, Temperature sensors, Air intake fan.

Feature	Description
Titanium heat exchanger	Corrosion-resistant for long-lasting performance
Digital control panel	Easy temperature and mode selection
Compressor unit	High-efficiency scroll compressor
Water flow sensor	Monitors water circulation for optimal operation
Temperature sensors	Monitors both air and water temperatures
Air intake fan	Quiet operation with optimized airflow
Power input connector	For electrical connection
Water inlet/outlet	Standard 1.5" or 2" plumbing connections
Eco mode	Energy-saving operation
POWER	Turns heat pump on/off

Installation

Unpack and inspect contents. Place on stable, level surface near pool equipment.

1. Position unit: Ensure minimum 24" clearance on all sides for proper airflow.
2. Connect plumbing: Install unions on water inlet and outlet ports.
3. Electrical connection: Connect to dedicated 240V circuit with proper grounding.
4. Connect to pool system: Integrate with existing pool pump and filter system.

WARNING! Unit is heavy; use proper lifting equipment. Ensure all electrical connections are made by qualified technician.

First-Time Setup

Power on heat pump; follow startup procedure.

1. Initial startup: Turn on power and wait for system initialization.
2. Set temperature: Use digital control to set desired pool temperature.
3. Configure operation modes: Select heating mode and schedule if available.
4. Test operation: Verify proper water flow and heating function.

CAUTION! Ensure proper water flow before starting heating operation.

Specifications

• Heating Capacity: 2.0 HP equivalent
• Power Requirements: 240V AC, 50/60Hz
• Water Connections: 1.5" or 2" plumbing
• Temperature Range: 50°F to 104°F operating range
• Heat Exchanger: Titanium construction
• Compressor: High-efficiency scroll type
• Control System: Digital microprocessor
• Operating Environment: Outdoor installation recommended

Controls and Settings

Access control panel for temperature and mode settings. Front Panel: POWER, TEMP UP/DOWN, MODE SELECT, ECO BUTTON.

Digital Display: Current temperature, Set temperature, Operating mode, Error codes, System status.

Temperature Settings: Adjust pool temperature in 1° increments. Modes: Heating, Cooling (if equipped), Eco mode, Standby. Advanced Settings: Temperature calibration, Timer settings, System diagnostics.

Connecting to Pool System

Water Connections: Standard plumbing connections. Electrical: Dedicated 240V circuit.

1. Turn off all power before making connections.
2. Install unions on water connections for future service.
3. Connect to pool return line after filter system.
4. Verify proper water flow direction.

Tip: Install isolation valves for easy maintenance and service.

Operation and Maintenance

Regular operation and maintenance procedures.

1. Daily Operation: Monitor temperature and system status.
2. Weekly: Check for proper water flow and clean debris from air intake.
3. Monthly: Inspect electrical connections and plumbing for leaks.
4. Seasonal: Perform comprehensive system check before heating season.
5. Annual: Professional service recommended for compressor and refrigerant system.

WARNING! Only qualified technicians should service refrigerant system.

Energy Efficiency Features

Eco Mode: Reduces energy consumption during partial load conditions. Smart Operation: Automatically adjusts operation based on ambient conditions. Timer Function: Program operation during off-peak hours for cost savings.

Care & Cleaning

Turn off power before cleaning. Clean air intake regularly. Keep area around unit clear of debris.

CAUTION! Do not use high-pressure water spray on electrical components.

Regulatory Information

UL certified for safety standards. EPA compliant for refrigerant usage. Copyright © 2025 Jandy; trademarks of Fluidra. For technical support, visit www.jandy.com or contact 1-800-227-1442.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit not starting	Power/water flow	Check power supply; verify proper water flow; reset breakers.
Poor heating performance	Airflow/temperature	Clean air intake; check ambient temperature; verify water flow.
Error codes displayed	System faults	Refer to error code chart in manual; contact service if persistent.
Water leaks	Connections/seals	Tighten plumbing connections; replace seals if necessary.
Unusual noises	Fan/compressor	Check for debris in fan; contact service for compressor issues.

Reset: Power cycle unit for minor issues.

Service: 1-800-227-1442; www.jandy.com