Jandy Pool System Manual

The Jandy Pool System is a comprehensive pool automation and filtration system designed for residential and commercial pools. It features advanced automation controls, energy-efficient pumps, precise chemical management, intuitive user interfaces, and remote access capabilities. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Chemical Management 8. Automation Features 9. Maintenance & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Control Panel, Variable Speed Pump, Filter System, Chemical Controller, Remote Access Module, Water Sensors.

Feature	Description
Control Panel	Touchscreen interface for system control and monitoring
Variable Speed Pump	Energy-efficient pump with adjustable flow rates
Filter System	Cartridge or DE filtration with pressure gauge
Chemical Controller	Automated pH and chlorine level management
Remote Access	Mobile app and web interface for remote control
Water Sensors	Monitors temperature, pH, and chlorine levels
POWER	Turns system on/off
MENU	Accesses system settings and programming
FILTER	Controls filtration cycles
CLEAN	Activates cleaning modes

Installation

Unpack and inspect all components. Ensure proper location near pool equipment pad.

Mount control panel: Install in dry, protected area away from direct water exposure.
Connect pump system: Follow plumbing diagram for proper water flow direction.
Install filtration system: Connect inlet and outlet pipes with appropriate seals.
Wire electrical connections: Use certified electrician for all electrical work.
Connect chemical feed lines: Install per local plumbing codes.

WARNING! Electrical shock hazard - disconnect power before installation. Ensure all connections are watertight.

First-Time Setup

Power on system; follow initial setup wizard.

System initialization: Press POWER to start; follow on-screen prompts.
Configure pool size: Enter pool volume for proper chemical dosing.
Set filtration schedule: Program daily run times based on pool usage.
Calibrate sensors: Follow calibration procedure for pH and chlorine sensors.
Connect to network: Set up Wi-Fi for remote access features.

CAUTION! Ensure proper chemical levels before starting automation. Test water chemistry manually first.

Specifications

Pump Motor: Variable speed, 1.5-3.0 HP
Filtration: Cartridge (200 sq ft) or DE (48 sq ft) options
Chemical Control: pH range 7.2-7.8, chlorine 1-3 ppm
Flow Rate: Adjustable 20-100 GPM
Power Requirements: 240V AC, 60Hz
Control Interface: 7-inch color touchscreen
Communication: Wi-Fi, Ethernet, RS-485
Operating Temp: 32°F to 122°F (0°C to 50°C)
Water Temp Range: 40°F to 104°F (4°C to 40°C)

Controls and Settings

Access system menu via touchscreen or mobile app. Front Panel: POWER, MENU, FILTER, CLEAN, LIGHTS, HEATER.

Remote Access: Mobile app provides full control, scheduling, and monitoring capabilities.

Filtration: Program run times, speeds, and cycles. Chemical: Set target levels, dosing schedules, and alarm thresholds. Temperature: Control heater and heat pump settings. Lighting: Program pool and spa light schedules. Cleaning: Set automatic cleaner operation times.

Connecting Devices

Supported devices: Heaters, lights, cleaners, water features, spa controls.

Turn off main power before connecting additional devices.
Connect via communication bus or relay outputs.
Configure device settings in system menu.
Test all connected devices for proper operation.

Tip: Label all connections for easy identification during maintenance.

Chemical Management

Automated chemical feeding with manual override capability.

Fill chemical reservoirs: Use approved pool chemicals only.
Set target levels: pH 7.4-7.6, chlorine 2-3 ppm.
Monitor consumption: Check chemical levels weekly.
Calibrate sensors: Monthly calibration recommended.
Override dosing: Manual control available for special circumstances.

WARNING! Handle chemicals with care. Wear protective equipment. Never mix different chemical types.

Automation Features

Schedule filtration, heating, lighting, and cleaning cycles. Remote monitoring and control via mobile app. Energy usage tracking and optimization. Vacation mode for extended absences. Freeze protection automatically activates in cold weather.

Maintenance & Cleaning

Weekly: Check chemical levels, clean skimmer baskets, inspect filter pressure. Monthly: Clean filter cartridges or backwash DE filter, calibrate sensors. Quarterly: Inspect pump seals, check electrical connections. Annually: Professional system inspection recommended.

CAUTION! Always disconnect power before performing maintenance. Never operate system with clogged filters.

Regulatory Information

UL Listed and CSA Certified. Complies with NSF/ANSI 50 standards. Meets local electrical and plumbing codes. Copyright © 2024 Jandy Products. All rights reserved. For technical support, visit www.jandy.com or contact 1-800-227-1442.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Pump not running	Power loss/overload	Check circuit breaker; reset if tripped; verify power supply.
Low flow rate	Clogged filter/blockage	Clean filter; check for obstructions in pipes and skimmers.
Chemical alarms	Sensor error/low chemicals	Calibrate sensors; refill chemical reservoirs; check for clogs.
No remote connection	Network issues	Check Wi-Fi signal; reboot router; verify network settings.
Error codes displayed	System faults	Note error code; consult manual; contact support if persistent.

Reset: Menu > System > Reset to factory defaults if needed.

Service: 1-800-227-1442; www.jandy.com