janome 1600p dbx manual

The Janome 1600P DBX is a high-performance industrial sewing machine designed for heavy-duty applications, featuring a built-in walking foot system, automatic thread trimmer, programmable needle positioning, variable speed control, and advanced bobbin winding system. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Accessories 7. Basic Operation 8. Maintenance Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Industrial sewing head, built-in walking foot, automatic thread trimmer, programmable controls, LED work light, knee lifter attachment.

Feature	Description
Built-in walking foot	Ensures even fabric feeding for multiple layers
Automatic thread trimmer	Cuts top and bobbin threads with single operation
Programmable needle positioning	Sets needle stop position (up/down)
Variable speed control	Adjustable sewing speed up to 1600 SPM
Knee lifter	Hands-free presser foot lifting
LED work light	Bright illumination of sewing area
Bobbin winding system	Automatic bobbin winding with thread cutter
Reverse stitch	Reinforces seam beginnings and endings
Thread tension control	Adjustable for different fabric types
Power switch	Main power control with safety lock

Installation

Unpack and inspect contents. Place on industrial table or stand.

Position machine: Ensure stable surface with adequate workspace.
Connect power: Plug into dedicated 110V AC outlet with proper grounding.
Install motor: Attach motor assembly according to diagram.
Connect foot pedal: Plug into designated port.
Oil machine: Apply recommended lubricant to specified points.

WARNING! Machine is heavy; use proper lifting equipment. Ensure power is disconnected during installation.

First-Time Setup

Power on machine; perform initial configuration.

Thread machine: Follow threading diagram for top thread and bobbin.
Set needle position: Program desired needle stop position.
Adjust thread tension: Test on scrap fabric and adjust as needed.
Calibrate foot pressure: Set for fabric thickness being used.
Test functions: Verify thread trimmer, reverse, and speed control.

CAUTION! Keep fingers away from needle area during operation. Always use proper safety guards.

Specifications

Stitch Type: Single needle lockstitch
Speed: Up to 1600 stitches per minute
Stitch Length: Adjustable 1-6mm
Needle System: DBx1 industrial needles
Presser Foot Lift: 10mm manual, 16mm with knee lifter
Bobbin Type: Industrial rotary hook with L-style bobbins
Motor: 550W industrial servo motor
Power Requirements: 110V AC, 60Hz
Machine Weight: 35kg (77 lbs)
Work Space: 280mm x 130mm

Controls and Settings

Access functions via control panel and mechanical adjustments.

Control Panel: Power switch, speed control dial, thread trimmer button, reverse stitch button, needle position selector.

Mechanical Adjustments: Thread tension dial, stitch length lever, presser foot pressure, feed dog height. Programming: Needle stop position (up/down), automatic backtack settings, thread trimmer timing.

Connecting Accessories

Foot pedal, knee lifter, additional work lights, specialized presser feet.

Turn off power before connecting accessories.
Match connectors to appropriate ports.
Secure all connections firmly.
Test accessory function before regular use.

Tip: Use only Janome-approved accessories for optimal performance and safety.

Basic Operation

Standard sewing procedures and advanced functions.

Power on: Switch main power to ON position.
Position fabric: Place under presser foot, lower foot.
Start sewing: Press foot pedal gently to begin.
Reverse stitching: Press reverse button at start/end of seam.
Thread trimming: Press trimmer button after stitching.
Needle positioning: Use position control to raise/lower needle.
Speed adjustment: Use dial to set maximum sewing speed.
Fabric feeding: Let walking foot guide fabric evenly.

WARNING! Never operate without proper training. Always disconnect power when not in use.

Maintenance Features

Automatic lubrication system, easy-access oil points, self-diagnostic functions, maintenance reminder indicators.

Care & Cleaning

Disconnect power before maintenance. Clean lint and debris regularly. Oil according to maintenance schedule.

CAUTION! Use only recommended lubricants. Do not use compressed air for cleaning near electrical components.

Regulatory Information

UL certified for electrical safety. CE marked for European compliance. Meets industrial sewing machine safety standards. Copyright © 2025 Janome; all rights reserved. For technical support, visit www.janome.com or contact 1-800-JANOME-1.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Thread breaking	Incorrect tension/damaged needle	Adjust tension; replace needle; check threading.
Skip stitches	Wrong needle type/bent needle	Use correct needle system; replace needle.
Machine not starting	Power connection/foot pedal	Check power supply; verify foot pedal connection.
Uneven feeding	Presser foot pressure/walking foot	Adjust foot pressure; clean walking foot mechanism.
Thread trimmer not working	Timing adjustment/thread buildup	Clean trimmer area; adjust trimmer timing.
Bobbin issues	Improper winding/insertion	Rewind bobbin properly; ensure correct insertion.

Reset: Power cycle machine if electronic functions malfunction.

Service: 1-800-JANOME-1; www.janome.com/support