Janome 2070 Instruction Manual

The Janome 2070 is a versatile sewing machine featuring 70 built-in stitches, one-step buttonhole, automatic needle threader, drop feed for free-motion sewing, adjustable stitch length and width, built-in needle plate window, top loading bobbin system, and multiple presser feet. Powered by standard household electrical outlet. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: 70 built-in stitches, automatic needle threader, drop feed lever, stitch selection dial, stitch width/length controls, bobbin winder, reverse stitch button, presser foot pressure dial.

Installation

Unpack and inspect contents. Place on stable sewing table.

1. Remove machine from packaging: Lift carefully from carrying case.
2. Place on stable surface: Ensure adequate workspace around machine.
3. Connect foot control: Plug into machine front port.
4. Connect power: Plug power cord into machine and electrical outlet.
5. Install accessories: Attach standard presser foot and needle.

WARNING! Machine is heavy; lift with care to avoid injury. Ensure all connections are secure.

First-Time Setup

Prepare machine for first use.

1. Install needle: Loosen needle clamp screw, insert needle with flat side to back, tighten screw.
2. Wind bobbin: Place thread on spool pin, guide thread through bobbin winder, press foot control.
3. Insert bobbin: Place bobbin in bobbin case with thread counterclockwise.
4. Thread upper thread: Follow numbered threading path on machine.
5. Use needle threader: Lower lever to automatically thread needle.
6. Raise bobbin thread: Hold upper thread, turn hand wheel toward you.

CAUTION! Always turn off power when changing needles or performing maintenance.

Specifications

• Stitches: 70 built-in stitches including utility, decorative, and stretch
• Buttonhole: One-step automatic buttonhole
• Stitch Length: Adjustable 0-4mm
• Stitch Width: Adjustable 0-5mm
• Needle Threader: Automatic
• Bobbin System: Top loading, jam-resistant
• Feed System: Drop feed for free-motion sewing
• Presser Feet: Multiple included for different functions
• Power Source: Standard household electrical outlet
• Dimensions: Compact design for easy storage

Controls and Settings

Main controls located on front and side of machine.

Front Panel: Stitch selection dial, stitch length dial, stitch width dial, reverse stitch button, bobbin winder, hand wheel.

Side Controls: Power switch, foot control socket, presser foot pressure dial, drop feed lever.

Stitch Selection: Turn dial to select desired stitch pattern. Stitch Length: Adjust for fabric type (shorter for fine fabrics, longer for heavy fabrics). Stitch Width: Adjust zigzag and decorative stitch width. Reverse Stitch: Hold button to sew in reverse for reinforcement. Presser Foot Pressure: Adjust for different fabric thicknesses.

Basic Sewing Operations

Fundamental sewing techniques and procedures.

1. Straight stitch: Select stitch pattern 1, adjust length as needed.
2. Zigzag stitch: Select appropriate zigzag pattern, adjust width and length.
3. Reverse stitching: Hold reverse button at beginning and end of seams.
4. Changing presser feet: Lift presser foot lever, press button on back of foot holder.
5. Adjusting tension: Upper tension dial for balanced stitches.
6. Using different stitches: Refer to stitch guide for appropriate applications.

Tip: Always test stitches on fabric scrap before sewing project.

Advanced Functions

Special features and advanced sewing techniques.

1. One-step buttonhole: Attach buttonhole foot, select buttonhole stitch, place fabric under foot.
2. Decorative stitches: Select decorative patterns, use appropriate presser feet.
3. Free-motion sewing: Lower feed dogs, use darning or embroidery foot.
4. Blind hem stitch: Use blind hem foot and appropriate stitch pattern.
5. Overcasting: Use overcast foot to finish raw edges.
6. Zipper insertion: Use zipper foot for precise zipper installation.
7. Button sewing: Attach button sewing foot for secure button attachment.

WARNING! Keep fingers away from moving needle. Always use proper presser feet.

Maintenance & Cleaning

Regular maintenance ensures optimal performance.

1. Daily cleaning: Remove lint from bobbin area and feed dogs.
2. Needle replacement: Change needle after every project or 8 hours of sewing.
3. Oiling: Apply sewing machine oil to designated points as per manual.
4. Bobbin case cleaning: Remove and clean bobbin case regularly.
5. Exterior cleaning: Wipe with soft, dry cloth.

CAUTION! Unplug machine before cleaning or maintenance. Use only recommended oils.

Regulatory Information

UL listed for safety standards. Complies with international electrical safety requirements. Copyright © Janome. For support, visit www.janome.com or contact authorized service centers. Serial number located on machine base.

Troubleshooting

Service: Contact authorized Janome service center for professional repairs.

Support: www.janome.com or local authorized dealer