Janome 6019 Instruction Manual

The Janome 6019 is a versatile mechanical sewing machine featuring 19 built-in stitches, 4-step buttonhole, drop feed for free-motion sewing, built-in needle threader, stitch length and width controls, reverse sewing, free arm capability, and built-in accessory storage. Powered by 120V AC, 60Hz. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation & Setup 3. First-Time Operation 4. Specifications 5. Controls and Settings 6. Stitch Selection 7. Basic Sewing Operations 8. Maintenance & Cleaning 9. Accessories 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Mechanical sewing machine with 19 stitches, free arm, built-in needle threader, stitch selection dial, reverse lever, feed dog control, and built-in accessory storage.

FeatureDescription
Built-in stitches19 utility and decorative stitches including straight, zigzag, and stretch stitches
4-step buttonholeEasy buttonhole creation with precise sizing
Drop feedFree-motion sewing for quilting and darning
Built-in needle threaderQuick and easy needle threading
Free armConvenient for sewing cuffs and sleeves
Stitch length controlAdjustable from 0-4mm
Stitch width controlAdjustable up to 5mm
Reverse sewing leverReinforce seams with reverse stitching
Built-in storageAccessory compartment in free arm
Power switchOn/off control with built-in light

Installation & Setup

Unpack and inspect contents. Place on stable sewing table.

  1. Remove machine from packaging and place on flat, stable surface.
  2. Install foot controller: Plug into machine and position for comfortable use.
  3. Connect power: Plug power cord into machine and wall outlet.
  4. Install needle: Loosen needle clamp screw, insert needle with flat side to back, tighten screw.
  5. Wind bobbin: Follow bobbin winding instructions in manual.
  6. Thread machine: Follow threading path indicated on machine.

WARNING! Keep fingers away from moving parts. Unplug when not in use.

First-Time Operation

Power on machine; test basic functions.

  1. Turn power switch to ON position; machine light should illuminate.
  2. Select straight stitch: Turn stitch selection dial to position 1.
  3. Test stitch: Place fabric under presser foot and gently press foot controller.
  4. Adjust stitch length: Turn stitch length dial for desired stitch length.
  5. Practice reverse stitching: Hold reverse lever while sewing.
  6. Test zigzag stitch: Turn stitch selection dial to zigzag position.

CAUTION! Always turn off power when changing needles or cleaning.

Specifications

Controls and Settings

Main controls: Stitch selection dial, stitch length dial, stitch width dial, reverse lever, feed dog control, bobbin winder, power switch.

Stitch Selection: Turn dial to select from 19 built-in stitches. Stitch Length: Adjust from 0-4mm (0 for darning). Stitch Width: Adjust up to 5mm for zigzag and decorative stitches. Reverse Lever: Hold down for reverse stitching. Feed Dog Control: Lower for free-motion sewing. Bobbin Winder: Wind bobbin before sewing.

Stitch Selection

Select from 19 built-in stitches for various sewing applications.

  1. Straight Stitch (Positions 1-3): Basic sewing, topstitching, basting
  2. Zigzag Stitch (Position 4): Seam finishing, appliqué, stretch fabrics
  3. Multiple Zigzag (Position 5): Elastic application, decorative work
  4. Blind Hem (Position 6): Nearly invisible hemming
  5. Stretch Stitches (Positions 7-9): Knits and stretch fabrics
  6. Decorative Stitches (Positions 10-19): Embellishment and decorative work

Tip: Always test stitch on scrap fabric before sewing project.

Basic Sewing Operations

Fundamental sewing techniques and operations.

  1. Threading: Follow numbered threading path on machine.
  2. Bobbin winding: Place thread on spool pin, guide through tension disc, wind bobbin.
  3. Needle threading: Use built-in needle threader for easy threading.
  4. Fabric feeding: Guide fabric gently; let feed dogs move fabric.
  5. Seam reinforcement: Use reverse lever at beginning and end of seams.
  6. Buttonholes: Follow 4-step buttonhole procedure.
  7. Free-motion sewing: Lower feed dogs for quilting and darning.

WARNING! Always use correct needle for fabric type.

Maintenance & Cleaning

Regular maintenance ensures optimal performance.

  1. Daily: Brush out lint from bobbin area and feed dogs.
  2. Weekly: Oil machine according to lubrication points in manual.
  3. Monthly: Clean tension discs and check needle plate for burrs.
  4. As needed: Replace needle after 8-10 hours of sewing.

CAUTION! Unplug machine before cleaning or maintenance.

Accessories

Standard accessories included with Janome 6019.

Regulatory Information

UL Listed: Certified for safety standards. Copyright © 2025 Janome America, Inc. All rights reserved. Janome is a registered trademark. For technical support and service, contact authorized Janome dealers or visit www.janome.com. Customer service: 1-800-631-0183.

Troubleshooting

SymptomPossible CauseCorrective Action
Thread breakingIncorrect threading/tensionRethread machine; check tension settings; use quality thread.
Needle breakingBent needle/wrong sizeReplace needle; ensure correct size for fabric.
Uneven stitchesThread tension/feedingAdjust tension; clean feed dogs; check presser foot pressure.
Machine not runningPower/pedal connectionCheck power cord; ensure pedal is plugged in properly.
Bobbin issuesIncorrect winding/insertionRewind bobbin evenly; ensure bobbin inserted correctly.
Skip stitchesNeedle/blunt needleReplace needle; ensure correct needle type for fabric.

Service: Contact authorized Janome service center for repairs.

Support: 1-800-631-0183; www.janome.com

Janome 6019 Instruction Manual © - All Rights Reserved 2025