The Janome 6260 is a high-performance sewing machine featuring 60 built-in stitches, one-step buttonhole, automatic needle threader, drop feed for free-motion sewing, adjustable presser foot pressure, built-in thread cutter, and speed control slider. This service manual provides comprehensive technical information for maintenance, repair, and troubleshooting of the Janome 6260 sewing machine. Below are key sections for specifications, maintenance procedures, troubleshooting, and technical diagrams.
Key technical specifications for the Janome 6260 sewing machine.
| Specification | Details |
|---|---|
| Stitch Types | 60 built-in stitches including utility, decorative, and stretch stitches |
| Buttonhole | One-step automatic buttonhole |
| Stitch Length | Adjustable up to 5mm |
| Stitch Width | Adjustable up to 7mm |
| Presser Feet | 6 included snap-on feet |
| Needle System | HAx1 SP |
| Bobbin | Front loading, class 15 transparent |
| Motor | DC servo motor with speed control |
| Power Requirements | 110V, 60Hz, 70W |
| Machine Dimensions | 15.4" W x 7.1" H x 6.7" D |
| Weight | 13.2 lbs |
Regular maintenance procedures to ensure optimal performance.
WARNING! Always unplug machine before performing any maintenance. Use only Janome-approved lubricants.
Step-by-step disassembly procedures for major components.
CAUTION! Document all disassembly steps for proper reassembly. Keep screws organized.
Detailed information about mechanical systems and adjustments.
Feed System: 7-point feed dog system with drop feed capability. Hook Assembly: Rotary hook with automatic bobbin winding. Needle Bar: Precision needle bar with thread take-up lever. Presser Foot: Adjustable pressure system (0-30mm). Stitch Selection: Cam-driven stitch pattern mechanism.
Timing Marks: Align timing marks on handwheel and hook drive gear. Needle Height: Set to 1.8mm above hook point at top dead center. Bobbin Case: Adjust tension to 180-220g pull test.
Common problems and their solutions for the Janome 6260.
| Symptom | Possible Cause | Corrective Action |
|---|---|---|
| Machine won't start | Power cord, foot control, main fuse | Check power connection; test foot control switch; replace 2A fuse |
| Skipped stitches | Needle, timing, thread tension | Replace needle; check hook timing; adjust upper tension |
| Thread breaking | Tension, needle, threading | Reduce tension; check for burrs on needle plate; rethread properly |
| Uneven feeding | Feed dogs, presser foot pressure | Clean feed dogs; adjust presser foot pressure; check for worn parts |
| Motor runs but no stitch | Handwheel clutch, drive belt | Engage handwheel clutch; check drive belt tension and condition |
| Error codes displayed | Sensor failure, main board issue | Reset machine; check sensor connections; test main board voltages |
Essential replacement parts for Janome 6260 service.
Note: Always use genuine Janome replacement parts for optimal performance.
Electrical schematics and connection diagrams.
Main Power Circuit: AC input to DC conversion with fuse protection. Motor Control: PWM speed control with feedback circuit. Control Panel: Matrix wiring for stitch selection buttons. Sensor Circuits: Position sensors for needle position and bobbin detection.
CAUTION! Always disconnect power before testing electrical circuits. Use multimeter for voltage measurements.
Calibration steps for precision adjustments.
Tip: Use calibration software and test fabrics for accurate adjustments.
Important safety information for service technicians.
Electrical Safety: Always unplug machine before service. Mechanical Safety: Keep hands clear of moving parts during testing. Chemical Safety: Use approved lubricants and cleaners only. Tool Safety: Use proper tools to avoid damage to components.
WARNING! Never bypass safety features or use non-approved parts.
Janome authorized service centers and technical support.
Technical Support: 1-800-631-0183 (Monday-Friday 9AM-5PM EST). Service Centers: Locate authorized service centers at www.janome.com. Parts Ordering: Order genuine parts through authorized dealers only. Training: Service technician training available through Janome Academy.
Warranty: 25-year limited warranty on mechanical parts, 5 years on electronic components.