Janome DC2007LE Manual

The Janome DC2007LE is a computerized sewing machine with 20 built-in stitches, automatic needle threader, drop feed for free-motion sewing, built-in buttonhole, adjustable stitch length and width, reverse sewing function, free arm capability, LED lighting, and easy stitch selection dial. Powered by 120V AC, 60Hz. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Computerized stitch selection, automatic needle threader, drop feed mechanism, free arm, built-in buttonhole, LED work light.

Installation and Setup

Unpack and inspect contents. Place on stable surface.

1. Remove machine from packaging: Lift carefully from carrying case.
2. Install foot control: Plug into machine port.
3. Connect power: Plug power cord into machine and wall outlet.
4. Install needle: Loosen needle clamp screw, insert needle with flat side to back.
5. Wind bobbin: Follow bobbin winding instructions.

WARNING! Machine is heavy; lift with care to avoid injury. Ensure stable placement.

First-Time Operation

Power on machine; follow setup procedures.

1. Thread machine: Follow threading path indicated on machine.
2. Use automatic needle threader: Push lever down and pull thread through.
3. Insert bobbin: Place bobbin in case with thread unwinding counterclockwise.
4. Select stitch: Turn stitch selection dial to desired pattern.
5. Test sew: Practice on scrap fabric first.

CAUTION! Keep fingers away from needle area during operation.

Specifications

• Stitches: 20 built-in stitches
• Stitch Length: 0-4mm adjustable
• Stitch Width: 0-5mm adjustable
• Buttonhole: One-step automatic
• Needle Threader: Automatic push-pull type
• Feed System: Drop feed for free-motion
• Lighting: LED work light
• Power Source: 120V AC, 60Hz
• Free Arm: Yes, convertible

Controls and Settings

Main controls: Stitch selection dial, stitch length dial, stitch width dial, reverse button, power switch.

Stitch Selection: Turn dial to select from 20 built-in stitches. Stitch Length: Adjust from 0-4mm for different fabric types. Stitch Width: Adjust from 0-5mm for decorative effects. Reverse: Hold button for backstitching. Drop Feed: Lever lowers feed dogs for free-motion work.

Stitch Selection

20 built-in stitches including straight, zigzag, stretch, and decorative patterns.

1. Turn stitch selection dial to desired pattern number.
2. Adjust stitch length for fabric type (shorter for delicate, longer for heavy).
3. Adjust stitch width for decorative effects.
4. Test stitch on scrap fabric before starting project.

Tip: Refer to stitch guide chart for recommended settings.

Basic Sewing Operations

Step-by-step sewing procedures.

1. Raise presser foot and position fabric.
2. Lower presser foot and begin sewing.
3. Guide fabric gently - don't push or pull.
4. Use reverse stitch at beginning and end of seams.
5. For free-motion: Lower feed dogs and move fabric manually.
6. For buttonholes: Use one-step automatic buttonhole function.

WARNING! Always turn power off when changing needles or cleaning.

Maintenance and Care

Regular maintenance ensures optimal performance.

1. Clean lint from bobbin area after each project.
2. Oil moving parts as directed in maintenance section.
3. Replace needle regularly (every 8-10 hours of sewing).
4. Cover machine when not in use to prevent dust accumulation.

CAUTION! Unplug machine before any maintenance or cleaning.

Regulatory Information

UL listed; complies with safety standards for household sewing machines. Copyright © 2025 Janome; trademarks of Janome America, Inc. For support, visit www.janome.com or contact 1-800-631-0183.

Troubleshooting

Service: 1-800-631-0183; www.janome.com