Janome DC2011 Instruction Manual

The Janome DC2011 is a computerized sewing machine with 60 built-in stitches, automatic needle threader, drop feed for free-motion sewing, built-in buttonhole styles, adjustable stitch length and width, speed control slider, start/stop button, reverse stitch button, and LCD display. Powered by standard household electrical outlet. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation & Setup 3. First-Time Operation 4. Specifications 5. Controls and Settings 6. Connecting Accessories 7. Stitch Selection & Usage 8. Advanced Functions 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: LCD display, automatic needle threader, stitch selection dial, speed control slider, bobbin winding system, drop feed lever, built-in LED light.

Feature	Description
LCD display	Shows selected stitch, stitch length/width settings
Automatic needle threader	Easy threading with push lever mechanism
Stitch selection dial	Select from 60 built-in stitches
Speed control slider	Adjust sewing speed from slow to fast
Start/stop button	Sew without foot control
Reverse stitch button	Reinforce stitching at beginning/end
Drop feed lever	Enable free-motion sewing and darning
Built-in buttonhole styles	One-step automatic buttonholes
Adjustable stitch length	0-5mm range
Adjustable stitch width	0-7mm range

Installation & Setup

Unpack and inspect contents. Place on stable sewing table.

Remove packaging materials and protective covers.
Attach foot control: Plug into machine port.
Install needle: Loosen needle clamp screw, insert needle with flat side to back.
Wind bobbin: Place thread on spool pin, guide thread through bobbin winding tension disk.
Insert bobbin: Place bobbin in case with thread unwinding counterclockwise.
Thread upper thread: Follow numbered threading path on machine.
Plug into power outlet.

WARNING! Keep fingers away from needle area during operation. Always turn off power when threading or changing accessories.

First-Time Operation

Power on machine; follow basic sewing steps.

Select straight stitch: Turn stitch selection dial to position 01.
Set stitch length: Adjust to 2.5 for medium stitch.
Place fabric under presser foot: Lower presser foot lever.
Begin sewing: Press foot control or start/stop button.
Guide fabric: Let machine feed fabric; do not pull.
Reverse stitching: Press reverse button at beginning and end of seam.
Raise needle: Turn handwheel toward you to highest position.
Remove fabric: Lift presser foot and pull fabric away.

CAUTION! Always raise needle before removing fabric to prevent needle breakage.

Specifications

Built-in Stitches: 60 stitches including utility, decorative, and stretch
Buttonholes: 6 one-step automatic styles
Stitch Length: 0-5mm adjustable
Stitch Width: 0-7mm adjustable
Needle Positions: Left, center, right
Presser Feet: Includes zigzag foot, zipper foot, buttonhole foot, blind hem foot
Bobbin: Front loading, Class 15 transparent bobbin
Lighting: Built-in LED work light
Power Source: Standard household electrical outlet
Dimensions: Standard sewing machine size with carrying handle

Controls and Settings

Access functions via stitch selection dial, LCD display, and control buttons.

Main Controls: Power switch, stitch selection dial, stitch length dial, stitch width dial, reverse stitch button, start/stop button, speed control slider, needle up/down button.

Stitch Selection: Turn dial to select from 60 stitches (01-60). Stitch Adjustment: Length (0-5mm), width (0-7mm). Special Functions: Automatic needle threader, drop feed, mirror image, memory function for stitch patterns. LCD Display: Shows selected stitch number, length/width settings, recommended presser foot.

Connecting Accessories

Standard accessories: Various presser feet, seam ripper, lint brush, needles, bobbins, spool holders.

Attach presser foot: Raise presser foot lever, position foot under ankle, lower lever to lock.
Change needle: Turn handwheel to raise needle, loosen needle clamp screw, replace needle.
Install auxiliary spool pin: For twin needle sewing or second spool.
Connect foot control: Plug into machine port before powering on.

Tip: Always use Janome brand accessories for optimal performance and safety.

Stitch Selection & Usage

Supports utility, decorative, and stretch stitches for various fabrics.

Select stitch: Turn dial to desired stitch number (01-60).
Adjust settings: Set length and width as needed for fabric.
Test stitch: Sew on scrap fabric to check tension and appearance.
Utility stitches: Straight stitch (01), zigzag (02-04), stretch stitches (05-10).
Decorative stitches: Ornamental patterns (11-50) for embellishment.
Buttonholes: One-step automatic (51-56) with sensor technology.
Blind hem: Stitch 57 for nearly invisible hemming.
Overcasting: Stitches 58-60 for edge finishing.

WARNING! Match needle and thread to fabric type. Use ballpoint needles for knits, sharp needles for wovens.

Advanced Functions

Automatic needle threader: Push lever down, hook thread through guide, release lever. Drop feed: Lower lever for free-motion quilting and darning. Memory function: Save frequently used stitch combinations. Mirror image: Create symmetrical stitch patterns. Needle up/down: Program needle stop position.

Care & Maintenance

Unplug before cleaning. Remove lint from bobbin area regularly. Oil moving parts as instructed in manual.

CAUTION! Use only sewing machine oil. Do not use household oils which can damage machine.

Regulatory Information

UL listed for electrical safety. Complies with international sewing machine standards. Copyright © Janome America, Inc. For support, visit www.janome.com or contact authorized service centers. Warranty: Limited warranty covering parts and labor for specified period.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Needle breaks	Incorrect insertion/bent needle	Ensure needle inserted fully with flat side to back; replace bent needle.
Thread bunching	Incorrect threading/tension	Re-thread upper and lower threads; check bobbin insertion.
Skipped stitches	Wrong needle/dull needle	Use correct needle type for fabric; replace dull needles.
Machine won't start	Power/position issues	Check power connection; ensure handwheel isn't locked.
Uneven stitches	Tension issues	Adjust upper tension; check bobbin tension.
Noise during operation	Lint/thread jam	Clean bobbin area; remove thread tangles.

Reset: Turn power off and on to reset computer functions.

Service: Contact authorized Janome service center; www.janome.com