Janome DC2015 Manual

The Janome DC2015 is a computerized sewing machine featuring 20 built-in stitches, one-step auto buttonhole, automatic needle threader, drop feed for free-motion sewing, built-in thread cutter, adjustable stitch length and width, top loading bobbin system, and LED lighting. Powered by standard household electrical outlet. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation & Setup 3. First-Time Operation 4. Specifications 5. Controls and Settings 6. Stitch Selection 7. Bobbin and Threading 8. Maintenance & Cleaning 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Computerized control panel, automatic needle threader, LED work light, drop feed lever, stitch selection dial, bobbin winding system.

Feature	Description
Built-in stitches	20 utility and decorative stitches
Auto buttonhole	One-step automatic buttonhole
Needle threader	Automatic needle threading system
Drop feed	Free-motion sewing capability
Built-in thread cutter	Convenient thread cutting
LED lighting	Bright work area illumination
Stitch length control	Adjustable from 0-4mm
Stitch width control	Adjustable up to 5mm
Top loading bobbin	Easy bobbin access and monitoring
Reverse stitch	Reinforcement stitching

Installation & Setup

Unpack and inspect contents. Place on stable sewing table.

Remove packaging materials and protective covers
Place machine on flat, stable surface
Connect foot controller to machine
Plug power cord into electrical outlet
Install needle following directional guide
Wind and insert bobbin
Thread upper thread through automatic needle threader

WARNING! Keep fingers away from needle area during operation. Always turn off power when threading or changing needle.

First-Time Operation

Power on machine; follow setup procedure.

Turn power switch to ON position
Select straight stitch using stitch selection dial
Practice on scrap fabric to test tension
Adjust stitch length and width as needed
Test reverse stitch function
Practice with different built-in stitches
Learn auto buttonhole function with buttonhole foot

CAUTION! Always use proper needle for fabric type. Replace bent or damaged needles immediately.

Specifications

Stitches: 20 built-in stitches
Buttonhole: One-step automatic
Needle Positions: Left, center, right
Stitch Length: 0-4mm adjustable
Stitch Width: Up to 5mm adjustable
Bobbin: Top loading, class 15 transparent
Lighting: LED work light
Needle System: HAx1 standard
Power Requirements: Standard household outlet
Dimensions: Standard sewing machine size

Controls and Settings

Access functions via control panel and dials. Front Panel: Power switch, stitch selection dial, stitch length dial, stitch width dial.

Additional Controls: Reverse stitch button, bobbin winder, drop feed lever, thread tension dial.

Stitch Selection: Turn dial to choose from 20 built-in stitches. Stitch Length: Adjust from 0-4mm for different fabrics. Stitch Width: Adjust up to 5mm for decorative stitches. Tension: Adjust thread tension dial for balanced stitches.

Stitch Selection

20 built-in stitches including straight, zigzag, stretch, and decorative patterns.

Turn stitch selection dial to desired stitch number
Adjust stitch length for fabric type (shorter for delicate, longer for heavy)
Adjust stitch width for zigzag and decorative stitches
Test stitch on scrap fabric before sewing project
Use reverse stitch to secure beginnings and endings
For buttonholes: Attach buttonhole foot and follow automatic sequence

Tip: Refer to stitch guide chart for recommended settings for different fabrics.

Bobbin and Threading

Top loading bobbin system with automatic needle threader.

Bobbin Winding: Place thread on spool pin, guide through bobbin winder tension, press foot controller
Bobbin Insertion: Place bobbin in case with thread pulling counterclockwise
Upper Threading: Follow numbered guide from spool to needle
Needle Threading: Use automatic needle threader for easy threading
Draw Up Bobbin Thread: Hold upper thread, turn hand wheel toward you

WARNING! Always raise needle to highest position before threading. Ensure presser foot is raised when threading.

Maintenance & Cleaning

Regular maintenance ensures optimal performance.

Unplug machine before cleaning
Remove needle plate to clean lint from bobbin area
Use small brush to remove dust and lint
Oil moving parts as recommended in manual
Wipe exterior with soft, dry cloth
Store with cover when not in use

CAUTION! Do not use compressed air for cleaning. Never oil without consulting manual.

Regulatory Information

UL Listed: Complies with safety standards for household sewing machines. Copyright © 2025 Janome; trademarks of Janome America, Inc. For technical support, visit www.janome.com or contact 1-800-631-0183. Made for household use only.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Machine won't start	Power connection	Check power cord connection; ensure foot controller is plugged in properly.
Thread breaking	Tension/thread quality	Reduce tension; check for rough spots on needle; use quality thread.
Skip stitches	Needle/thread mismatch	Replace needle; ensure correct needle for fabric; rethread machine.
Bobbin thread bunching	Bobbin threading	Rethread bobbin; ensure bobbin is inserted correctly in case.
Uneven stitches	Tension settings	Adjust thread tension; check for lint in tension discs.

Reset: Turn machine off and on to reset computerized functions.

Service: 1-800-631-0183; www.janome.com