janome dc2101 manual pdf

The Janome DC2101 is a computerized sewing machine featuring 60 built-in stitches, one-step auto buttonhole, automatic needle threader, drop feed for free-motion sewing, adjustable stitch length and width, built-in thread cutter, and easy reverse stitching. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Computerized control panel, automatic needle threader, drop feed lever, stitch selection dial, built-in thread cutter, free arm capability.

Installation & Setup

Unpack and inspect all contents. Place on stable sewing surface.

1. Remove packaging materials and protective covers from machine.
2. Connect foot controller to machine and power outlet.
3. Install needle: Loosen needle clamp screw, insert needle with flat side to back.
4. Wind bobbin: Place thread on spool pin, follow threading guide.
5. Insert bobbin: Drop bobbin into case with thread clockwise.
6. Thread upper thread: Follow numbered threading path.

WARNING! Keep fingers away from needle area during operation. Unplug when not in use.

Basic Operation

Power on machine; select desired stitch and settings.

1. Select stitch: Turn stitch selection dial to desired pattern.
2. Adjust settings: Set stitch length and width as needed.
3. Thread machine: Follow automatic needle threader or manual threading.
4. Begin sewing: Place fabric under presser foot, lower foot, press pedal.
5. Reverse stitching: Press reverse button to secure stitches.
6. Cut thread: Use built-in thread cutter when finished.

CAUTION! Always lower presser foot before sewing. Keep work area well-lit.

Specifications

• Stitches: 60 built-in stitches
• Buttonhole: One-step automatic
• Needle Positions: Multiple needle positions available
• Stitch Length: Adjustable up to 5mm
• Stitch Width: Adjustable up to 7mm
• Bobbin: Top-loading, jam-resistant
• Free Arm: Yes, convertible
• Presser Feet: Multiple included
• Power Supply: 110V, 60Hz (US standard)
• Warranty: 25-year limited warranty

Controls and Functions

Access functions via control panel and dials. Front Panel: Stitch selection dial, stitch length dial, stitch width dial, reverse button.

Control Panel: Power switch, stitch pattern indicators, needle up/down position, automatic needle threader.

Stitch Selection: Turn dial to select from 60 built-in stitches. Stitch Length: Adjust from 0-5mm. Stitch Width: Adjust from 0-7mm. Reverse: Press for reinforcement stitching. Needle Position: Set needle stop up or down position.

Stitch Selection

Choose from 60 utility, decorative, and stretch stitches.

1. Utility stitches: Straight stitch, zigzag, overcast, blind hem
2. Decorative stitches: Scallop, honeycomb, leaf patterns
3. Stretch stitches: For knit fabrics and elastic materials
4. Buttonhole: One-step automatic buttonhole
5. Specialty stitches: Quilting, applique, satin stitches

Tip: Test stitch on scrap fabric before sewing project.

Maintenance & Cleaning

Unplug machine before cleaning. Regular maintenance ensures optimal performance.

1. Clean bobbin area: Remove bobbin case and clean lint
2. Oil machine: Apply sewing machine oil as directed
3. Change needle: Replace needle regularly or when damaged
4. Clean exterior: Use soft, dry cloth only
5. Storage: Cover machine when not in use

CAUTION! Do not use compressed air for cleaning. Use only recommended oils.

Accessories

Standard accessories included with Janome DC2101.

• General purpose foot
• Zigzag foot
• Buttonhole foot
• Zipper foot
• Overedge foot
• Blind hem foot
• Bobbin (extra)
• Needles (assorted)
• Seam ripper/lint brush
• Screwdriver
• Spool holders

Regulatory Information

UL Listed: Complies with US safety standards. FCC Part 15: Class B digital device; complies with interference limits. Copyright © Janome America, Inc. For support, visit www.janome.com or contact 1-800-631-0183.

Troubleshooting

Reset: Turn machine off and on to reset computerized functions.

Service: 1-800-631-0183; www.janome.com