Janome DC2101 User Manual

The Janome DC2101 is a computerized sewing machine with 100 built-in stitches, one-step buttonhole, automatic needle threader, drop feed for free-motion sewing, built-in needle plate window, top-loading bobbin system, adjustable stitch length and width, speed control slider, reverse stitch button, and built-in thread cutter. Powered by 120V AC, 60Hz. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Computerized control panel, built-in stitches, automatic needle threader, drop feed system, top-loading bobbin, speed control slider.

Installation

Unpack and inspect contents. Place on stable sewing table.

1. Remove machine from packaging: Carefully lift machine from box.
2. Attach accessories: Install foot controller, power cord, and accessories.
3. Position machine: Place on flat, stable surface at comfortable height.
4. Connect power: Plug into AC power outlet.

WARNING! Machine is heavy; lift with care to avoid injury. Ensure stable surface placement.

First-Time Setup

Power on machine; follow setup procedures.

1. Thread machine: Follow threading diagram; use automatic needle threader.
2. Wind bobbin: Use built-in bobbin winder.
3. Insert bobbin: Place in top-loading bobbin case.
4. Select stitch: Choose from 100 built-in stitches.
5. Test sewing: Practice on scrap fabric.

CAUTION! Keep fingers away from needle area during operation.

Specifications

• Stitches: 100 built-in stitches
• Buttonhole: One-step automatic
• Needle System: HAx1 needle
• Bobbin: Top-loading, jam-resistant
• Stitch Length: Adjustable up to 5mm
• Stitch Width: Adjustable up to 7mm
• Speed: Up to 820 stitches per minute
• Power Source: 120V AC, 60Hz
• Dimensions: Standard sewing machine size

Controls and Settings

Access functions via control panel and dials.

Control Panel: Stitch selection dial, stitch length/width controls, reverse stitch button, needle up/down button.

Basic Settings: Stitch selection (1-100), stitch length (0-5mm), stitch width (0-7mm), needle position. Advanced Functions: Mirror imaging, memory function, automatic thread tension. Speed Control: Adjustable via slider on front panel.

Basic Sewing Operations

Straight stitch, zigzag, and basic decorative stitches.

1. Select stitch: Turn dial to desired stitch number.
2. Adjust settings: Set length and width as needed.
3. Position fabric: Lower presser foot.
4. Start sewing: Press foot controller gently.
5. Reverse: Press reverse button to secure stitches.
6. Finish: Raise needle, lift presser foot, remove fabric.

Tip: Always test stitch settings on scrap fabric first.

Advanced Functions

One-step buttonhole, decorative stitches, free-motion sewing.

1. Buttonhole: Attach buttonhole foot; select buttonhole stitch.
2. Decorative stitches: Choose from built-in patterns.
3. Free-motion: Lower feed dogs for quilting and embroidery.
4. Memory function: Store frequently used stitch combinations.
5. Mirror imaging: Create symmetrical stitch patterns.

WARNING! Use appropriate presser feet for each function.

Maintenance & Cleaning

Unplug before maintenance. Clean lint regularly; oil as recommended.

1. Daily: Remove lint from bobbin area and feed dogs.
2. Weekly: Clean race hook and surrounding areas.
3. Monthly: Oil moving parts as per manual instructions.
4. As needed: Replace needle regularly.

CAUTION! Do not use compressed air; unplug during cleaning.

Regulatory Information

UL listed; complies with safety standards for household sewing machines. Copyright © 2025 Janome; trademarks of Janome America, Inc. For support, visit www.janome.com or contact 1-800-631-0183.

Troubleshooting

Reset: Turn machine off and on to reset computerized functions.

Service: 1-800-631-0183; www.janome.com