janome decor computer dc3018 manual

The Janome Decor Computer DC3018 is a computerized sewing machine with 30 built-in stitches, automatic one-step buttonhole, drop feed for free-motion sewing, built-in needle threader, adjustable stitch length and width, reverse sewing function, and free arm capability. Features include LCD display, automatic thread cutter, speed control slider, and multiple presser feet. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation & Setup 3. First-Time Operation 4. Specifications 5. Controls and Functions 6. Stitch Selection 7. Buttonhole Function 8. Maintenance & Cleaning 9. Accessories 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Computerized control panel, LCD display, automatic needle threader, drop feed mechanism, free arm, built-in stitches, buttonhole function.

FeatureDescription
Built-in stitches30 utility, decorative, and stretch stitches
Automatic buttonholeOne-step buttonhole with memory function
LCD displayShows selected stitch, length, and width settings
Automatic needle threaderEasy threading with built-in mechanism
Drop feedFree-motion sewing capability
Free armFor sewing sleeves and hard-to-reach areas
Reverse sewingReinforce seams with reverse stitch button
Speed controlAdjustable sewing speed with slider
Automatic thread cutterBuilt-in thread cutting function
Stitch length/widthAdjustable settings for customization

Installation & Setup

Unpack and inspect contents. Place on stable surface.

  1. Remove machine from packaging: Lift carefully from carrying case.
  2. Install foot controller: Plug into machine's foot controller port.
  3. Connect power: Plug power cord into machine and electrical outlet.
  4. Install needle: Ensure flat side faces back, tighten needle clamp screw.
  5. Wind bobbin: Follow bobbin winding instructions in manual.
  6. Thread machine: Use automatic needle threader for easy threading.

WARNING! Machine is heavy; lift with care to avoid injury. Ensure stable work surface.

First-Time Operation

Power on machine; follow setup procedures.

  1. Select stitch: Use stitch selection dial to choose desired pattern.
  2. Adjust settings: Set stitch length and width as needed.
  3. Test sew: Use scrap fabric to test stitch quality and tension.
  4. Thread tension: Adjust upper thread tension if necessary.
  5. Practice functions: Try reverse stitch, automatic buttonhole.

CAUTION! Keep fingers away from needle area during operation.

Specifications

Controls and Functions

Access functions via control panel and LCD display.

Control Panel: Stitch selection dial, stitch length/width controls, reverse button, automatic thread cutter, speed control slider.

LCD Display: Shows selected stitch number, length, width settings. Stitch Selection: Turn dial to choose from 30 stitches. Stitch Adjustment: Length (0-5mm), Width (0-7mm). Reverse: Press to reinforce seams. Thread Cutter: Automatic cutting function. Speed Control: Slider for sewing speed adjustment.

Stitch Selection

30 built-in stitches including utility, decorative, and stretch stitches.

  1. Turn stitch selection dial to desired stitch number.
  2. Check LCD display for stitch confirmation.
  3. Adjust stitch length and width as needed.
  4. Test on scrap fabric before sewing project.
  5. Use appropriate presser foot for selected stitch.

Tip: Refer to stitch chart for recommended applications.

Buttonhole Function

Automatic one-step buttonhole with memory.

  1. Attach buttonhole foot.
  2. Select buttonhole stitch on dial.
  3. Place fabric under foot, lower presser foot.
  4. Press foot controller to sew complete buttonhole.
  5. Machine automatically measures and sews buttonhole.
  6. Use automatic thread cutter when finished.

WARNING! Always test buttonhole on scrap fabric first.

Maintenance & Cleaning

Unplug before maintenance. Regular cleaning ensures optimal performance.

  1. Clean lint from bobbin area after each project.
  2. Oil machine as specified in maintenance schedule.
  3. Wipe exterior with soft, dry cloth.
  4. Store in carrying case when not in use.

CAUTION! Use only Janome recommended oils and cleaners.

Accessories

Standard accessories included: All-purpose foot, zipper foot, buttonhole foot, button sewing foot, blind hem foot, overedge foot, seam ripper, lint brush, needles, bobbins, screwdriver, spool caps.

Regulatory Information

UL listed for safety standards. Complies with FCC regulations for digital devices. Copyright © Janome America, Inc. For support, visit www.janome.com or contact customer service at 1-800-631-0183.

Troubleshooting

SymptomPossible CauseCorrective Action
Machine not runningPower connectionCheck power cord connection; ensure foot controller plugged in.
Thread breakingTension/thread qualityAdjust thread tension; use quality thread; check needle.
Skipped stitchesNeedle/blunt needleReplace needle; ensure correct needle type for fabric.
Poor stitch qualityThreading/tensionRe-thread machine; clean lint from bobbin area.
Buttonhole not workingFoot attachmentEnsure buttonhole foot properly attached; test on scrap.

Reset: Turn machine off and on to reset computer functions.

Service: 1-800-631-0183; www.janome.com

janome decor computer dc3018 manual © - All Rights Reserved 2025