Janome MOD-30 Manual

The Janome MOD-30 is a computerized sewing machine with 30 built-in stitches, one-step buttonhole, automatic needle threader, drop feed for free-motion sewing, built-in thread cutter, adjustable stitch length and width, top-loading bobbin system, LED lighting, speed control slider, reverse sewing button, and easy stitch selection dial. Powered by standard household electrical outlet. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Computerized control panel, stitch selection dial, automatic needle threader, drop feed lever, bobbin system, LED work light, foot pedal, accessory storage.

Feature	Description
Built-in stitches	30 utility, decorative, and stretch stitches
One-step buttonhole	Automatic buttonhole creation
Automatic needle threader	Easy threading system
Drop feed lever	For free-motion sewing and quilting
Built-in thread cutter	Convenient thread trimming
Top-loading bobbin	Easy bobbin insertion and monitoring
LED work light	Bright illumination of sewing area
Speed control slider	Adjustable sewing speed
Reverse sewing button	For reinforcing stitches
Stitch length/width adjustment	Customizable stitch settings

Installation and Setup

Unpack and inspect all contents. Place on stable, flat surface.

1. Remove packaging materials and protective covers.
2. Attach power cord to machine and plug into electrical outlet.
3. Install foot pedal and connect to machine.
4. Install needle following arrow direction.
5. Wind and insert bobbin.
6. Thread upper thread through automatic needle threader.

WARNING! Keep fingers away from needle area during operation. Always turn off power when not in use.

First-Time Operation

Power on machine; follow setup procedures.

1. Select straight stitch using stitch selection dial.
2. Place fabric under presser foot and lower foot lever.
3. Press foot pedal gently to begin sewing.
4. Use reverse button to secure stitches at beginning and end.
5. Adjust stitch length and width as needed for your project.
6. Practice with scrap fabric before starting actual projects.

CAUTION! Always use proper needle for fabric type. Replace bent or damaged needles immediately.

Specifications

• Built-in Stitches: 30 stitches including utility, decorative, and stretch
• Buttonhole: One-step automatic buttonhole
• Needle Positions: Left, center, right needle positions
• Stitch Length: Adjustable up to 5mm
• Stitch Width: Adjustable up to 7mm
• Bobbin System: Top-loading, jam-resistant
• Lighting: LED work light
• Power Supply: Standard household electrical outlet
• Dimensions: Compact design for easy storage
• Weight: Lightweight and portable

Controls and Settings

Access functions via control panel and dials. Front Panel: Power switch, stitch selection dial, stitch length dial, stitch width dial, reverse button.

Additional Controls: Drop feed lever, automatic needle threader, thread cutter, presser foot lever, hand wheel.

Stitch Settings: Length (0-5mm), Width (0-7mm), needle position (left/center/right). Special Functions: Reverse sewing, automatic thread cutter, speed control, built-in needle threader.

Stitch Selection

30 built-in stitches for various sewing applications.

1. Turn stitch selection dial to choose desired stitch pattern.
2. Adjust stitch length dial for shorter or longer stitches.
3. Adjust stitch width dial for narrower or wider stitches.
4. Select appropriate presser foot for chosen stitch.
5. Test stitch on scrap fabric before sewing project.
6. Use reverse button to secure stitches at beginning and end.

Tip: Refer to stitch guide for recommended uses of each stitch pattern.

Threading and Bobbin

Proper threading ensures smooth operation.

1. Raise presser foot and raise needle to highest position.
2. Follow numbered threading path on machine.
3. Use automatic needle threader for easy needle threading.
4. Wind bobbin with same thread as upper thread for best results.
5. Insert bobbin with thread unwinding counterclockwise.
6. Pull bobbin thread up through needle plate.

WARNING! Always thread with presser foot raised and power off.

Maintenance and Care

Regular maintenance ensures optimal performance.

1. Clean lint and dust from bobbin area regularly.
2. Oil moving parts as recommended in manual.
3. Replace needles regularly or when damaged.
4. Use proper needles for different fabric types.
5. Store machine covered when not in use.
6. Use genuine Janome parts and accessories.

CAUTION! Unplug machine before cleaning or maintenance.

Accessories

Standard accessories included with Janome MOD-30.

Accessory	Use
All-purpose foot	General sewing
Zipper foot	Installing zippers
Buttonhole foot	Creating buttonholes
Bobbin (extra)	Additional bobbin
Needles	Replacement needles
Seam ripper	Removing stitches
Brush	Cleaning lint
Screwdriver	Adjustments

Troubleshooting

Symptom	Possible Cause	Corrective Action
Machine not running	Power connection	Check power cord; ensure machine is turned on
Thread breaking	Improper threading/tension	Re-thread machine; check tension settings
Uneven stitches	Thread tension/needle	Adjust tension; replace needle; check threading
Fabric not feeding	Feed dogs lowered	Raise drop feed lever; clean feed dogs
Needle breaking	Bent needle/wrong size	Replace needle; use correct needle for fabric
Bobbin issues	Improper insertion/winding	Re-insert bobbin; re-wind bobbin evenly

Service: Contact authorized Janome service center for repairs.

Support: Visit www.janome.com or contact customer service for assistance.