janome scan n sew manual

The Janome Scan N Sew is a computerized sewing machine with advanced scanning capabilities, automatic thread tension, built-in stitches, LCD display, automatic needle threader, drop feed for free-motion sewing, speed control slider, start/stop button, reverse stitch button, and programmable stitch patterns. Powered by 120V AC, 60Hz. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Accessories 7. Scanning and Sewing Operations 8. Maintenance Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: LCD display with stitch selection, Automatic needle threader, Drop feed lever, Bobbin winding system, Presser foot pressure dial, Stitch width/length dials, Foot pedal connector, Power switch.

Feature	Description
LCD Display	Shows selected stitch pattern and settings
Automatic Needle Threader	Assists with threading needle automatically
Drop Feed Lever	Lowers feed dogs for free-motion sewing
Bobbin Winding System	Automatically winds bobbin from upper thread
Presser Foot Pressure Dial	Adjusts pressure for different fabric types
Stitch Width/Length Dials	Controls stitch dimensions and density
Foot Pedal Connector	For foot control operation
Power Switch	Turns machine on/off
Speed Control Slider	Adjusts maximum sewing speed
Start/Stop Button	Starts and stops sewing without foot pedal

Installation

Unpack and inspect contents. Place on stable sewing table.

Remove machine from packaging: Lift carefully from carrying case.
Install foot pedal: Connect to machine port.
Connect power: Plug power cord into machine and wall outlet.
Install needle: Loosen needle clamp screw, insert needle with flat side to back.
Wind bobbin: Follow bobbin winding instructions.

WARNING! Machine contains sharp needles; handle with care to avoid injury. Ensure all connections are secure.

First-Time Setup

Power on machine; follow initial setup procedures.

Thread machine: Follow threading path indicated on machine.
Insert bobbin: Place bobbin in case with thread unwinding counterclockwise.
Select basic stitch: Choose straight stitch for initial testing.
Adjust tension: Set to medium (4-5) for standard fabrics.
Test sew: Use scrap fabric to verify proper operation.

CAUTION! Keep fingers away from needle area during operation. Always turn off when threading.

Specifications

Machine Type: Computerized sewing machine with scanning
Stitches: 50+ built-in stitches including utility, decorative, and buttonholes
Scanning System: Automatic fabric detection and stitch adjustment
Needle System: HAx1 standard domestic needles
Bobbin: Class 15 transparent bobbin
Max Sewing Speed: 820 stitches per minute
Display: LCD with stitch selection and settings
Power Source: 120V AC, 60Hz
Weight: 15.4 lbs (7 kg)

Controls and Settings

Access functions via LCD display and control buttons. Front Panel: POWER, Stitch selection buttons, Reverse stitch, Needle up/down, Start/stop.

Display Controls: Stitch pattern selection, Stitch length/width adjustment, Mirror image, Memory functions, Scanning mode activation.

Basic Settings: Thread tension (0-9), Presser foot pressure, Feed dog position, Needle position. Advanced: Scan sensitivity, Auto-lock stitch, Programmable stitch combinations, Buttonhole memory.

Connecting Accessories

Foot pedal: Standard connector. Additional feet: Snap-on system. Extension table: Attaches to free arm.

Turn off machine before changing accessories.
Snap on presser feet: Lower presser foot lever, align foot with shank.
Install extension table: Slide onto free arm until it clicks into place.
Connect auxiliary lamp: Plug into accessory port if available.

Tip: Always use genuine Janome accessories for optimal performance.

Scanning and Sewing Operations

Supports automatic fabric scanning and stitch adjustment.

Activate scan mode: Press SCAN button on control panel.
Place fabric: Position under presser foot in scanning area.
Start scanning: Machine automatically detects fabric type and thickness.
Auto-adjustment: Machine sets optimal stitch length, tension, and pressure.
Begin sewing: Press start button or foot pedal to begin.
Manual override: Adjust settings as needed during sewing.
Pattern selection: Choose from built-in stitches using selection dial.
Memory functions: Save custom settings for frequently used fabrics.

WARNING! Keep hands clear of scanning area. Do not force fabric through scanner.

Maintenance Features

Automatic Maintenance Reminder: LCD displays when cleaning is needed. Self-diagnostic System: Detects common issues and suggests solutions. Oil-free Maintenance: Most components require no regular oiling.

Care & Cleaning

Unplug before cleaning. Use soft brush to remove lint from bobbin area and feed dogs.

CAUTION! Do not use compressed air or liquids for cleaning. Store in dry area away from dust.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © 2006 Janome; trademarks of Janome America, Inc. Safety Certified: UL and CSA approved. For support, visit www.janome.com or contact 1-800-631-0183.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Machine won't start	Power connection/foot pedal	Check power cord; ensure foot pedal is connected properly.
Thread breaking	Tension/thread quality	Reduce tension; use better quality thread; check needle.
Scanning not working	Fabric placement/settings	Ensure fabric is flat in scanning area; reset scan settings.
Uneven stitches	Timing/tension issues	Check bobbin insertion; adjust upper thread tension.
Needle breaks	Wrong needle/bent needle	Replace with correct needle type; ensure needle is straight.

Reset: Turn machine off and on to reset computer functions.

Service: 1-800-631-0183; www.janome.com