Janome Serger 8002D Manual

The Janome Serger 8002D is a professional-grade 2/3/4 thread overlock sewing machine with differential feed, built-in rolled hem capability, color-coded threading system, free arm capability, built-in thread cutter, adjustable stitch length and width, and easy tension control system. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Color-coded threading system, differential feed, free arm, built-in rolled hem, adjustable stitch controls, built-in thread cutter.

Unpacking and Setup

Unpack and inspect all contents. Place on stable sewing surface.

1. Remove machine from packaging: Carefully lift machine from box.
2. Attach power cord: Plug into machine and wall outlet.
3. Install foot control: Connect to machine port.
4. Thread machine: Follow color-coded threading guide.
5. Insert needle: Ensure proper orientation and secure.

WARNING! Machine is heavy; lift with care to avoid injury. Ensure stable surface placement.

Basic Operation

Power on machine; test stitches on scrap fabric first.

1. Select stitch type: Choose 2, 3, or 4 thread overlook.
2. Adjust stitch length: Set between 1-4mm for fabric type.
3. Adjust stitch width: Set between 3-7mm as needed.
4. Set differential feed: Adjust for fabric stretch characteristics.
5. Begin sewing: Guide fabric through without pulling.

CAUTION! Keep fingers away from moving needle and cutting blade.

Specifications

• Machine Type: 2/3/4 Thread Overlock Serger
• Stitch Length: 1-4mm adjustable
• Stitch Width: 3-7mm adjustable
• Differential Feed: 0.7-2.0 ratio
• Speed: Up to 1300 stitches per minute
• Rolled Hem: Built-in conversion
• Threading: Color-coded system
• Power Source: 120V AC, 60Hz
• Weight: Approximately 15.4 lbs (7 kg)
• Warranty: 25-year limited warranty

Controls and Settings

Access all controls from front and top of machine. Main Controls: Power switch, stitch length dial, stitch width dial, differential feed dial, tension dials.

Thread Tension: Upper looper, lower looper, right needle, left needle tension dials. Stitch Selection: 2-thread, 3-thread, 4-thread overlook stitches. Rolled Hem: Quick conversion lever. Presser Foot: Lever for raising/lowering.

Threading Instructions

Follow color-coded threading path for each thread.

1. Turn power off before threading.
2. Follow numbered threading sequence.
3. Use color-coded guides (blue, green, red, yellow).
4. Ensure threads are properly seated in tension discs.
5. Test stitch on scrap fabric after threading.

Tip: Always thread with presser foot raised to open tension discs.

Stitch Selection

Supports multiple overlook stitch types for various fabrics.

1. 2-thread overlook: For lightweight fabrics and rolled hems
2. 3-thread overlook: Standard finishing for most fabrics
3. 4-thread safety stitch: Extra strength for seams
4. Rolled hem: Convert for delicate edge finishing
5. Flatlocking: For decorative seams and appliqué

WARNING! Always test stitch on scrap fabric before sewing project.

Maintenance & Cleaning

Unplug before cleaning. Remove lint buildup regularly.

1. Clean feed dogs and loopers with brush provided
2. Oil machine as per maintenance schedule
3. Check needle regularly for damage
4. Clean tension discs periodically
5. Store with cover when not in use

CAUTION! Do not use compressed air for cleaning. Use only recommended oils.

Accessories

Standard accessories included: Screwdriver, tweezers, lint brush, oil, spare needles, accessory pouch.

Warranty Information

25-year limited warranty covering mechanical parts. 5-year electronic components. 1-year labor. Warranty registration card included. For service, contact authorized Janome dealers. Keep original receipt for warranty claims.

Troubleshooting

Service: Contact authorized Janome dealer for technical service.

Support: 1-800-631-0183; www.janome.com